Видео

Great I came here for the music. What did you say?

I am a 70-year-old woman and after watching this video I am fixing the back hatch latch all by myself thank you so much

Why re there Channels 2, 3 and 4? How to use them?

Pov a guy in 2024 trying to get ios 14 and a better chip set after his 6+ only got 4 years of support

he said 4 side pieces....

Trying to install this 1060 as a soft open function ( as you show in the video). Using a 24" wide door. Im looking at the instructions, and they're rather confusing, in the fact that there's multiple directions for soft open and close. Each set of directions is not the same ( as far as distance to put the arm from the rough wall, and distance from edges to mount the door plates. After watching your video, it made it quite clear how it works and how to install. One set of directions says - for 24" doors, actuator will be flush with end of track. So i figured I'd go with that. However, when i get the arm up in the track and slide the end of the arm until its flush with the end of the track, i attempt to tighten it down. Problem I'm having is the screw is very tight in the threads of the top part of the clamp. When i try to tighten it down, the top part of the clamp turns and winds up sideways in the track. The top clamp has a "finger" on it that should hold it in position to the bottom clamp. Ive tried to run the screw in and out a few times to clean up the threads, but doesnt matter. The screw still gets tight, and winds up turning the upper half of the clamp. If i could tighten the screw down, the finger would fit into the bottom clamp and i could tighten it down. If i pre tighten the upper clamp so the finger stays in the notch, than i cant slide it over the track. Plus i noticed the bend in the arm isnt exactly 90°, should it be? Thanks

Good job

Thank you

Our door seal has recently had water pooling in the gap, but I wasn't aware that there was a drain in that location. I wouldn't be surprised if it is clogged like this, so this is definitely helpful just to narrow down the source of my issue. I bought my washer used several years ago, and had to replace the drain pump already. I thought it also had a bad intake valve, but it turned out that one of the wires just wasn't clipped in place all the way. Otherwise, it has been pretty reliable and fairly easy to repair.

I just got my license and don't know how to pump gas. I'll be trying this in a few, thank you!!!

how much would you say the whole thing cost you (building the whole garage)

Why 3 pieces at the Ridge instead of 1 large Gusset

Bro thank you so much, I stole my dad’s car to go to the gym and I almost ran out of gas, you freaking saved me bro: AFTER SIX YEARS. I tried pumping and it didn’t work till I realize I had to pay first

Question 1: Do I need to put masonry cement between multiple cement blocks? Question 2: Do I need to attach 4x4 to masonry blocks somehow? (Hurricane worries)

Do you backfill these trenches or just pour on the plumbing directly

5:03 5:05

249 & 1/2 Blackman st

I just used this video to change the door gasket. I put it back together & now my washer is squeaking really bad. What did I do?

Thank you so much! Such clear instructions. Really appreciate it!

Im 14 lol, Im watching this so i can be ready to have my car when im 16😂 🚘

$28 in 2024😮‍💨

Thanks so much

Very informative, thank you for the clear instructions

You should put Diesel in it.

Very very helpful , thank you so much!

I think you just saved me a lot of BS. 6 years ago, still helps.

God Lee you’re doing a lot of crap for the ac unit.

I replaced mine recently, for some reason it won't lock. I am wondering because I installed the trunk while it was open maybe got too much slack? I see the black pin/knob on the inside move up and down when I hit the lock and unlock button...

Is there a piece at the bottom to keep the door from swaying too much?

I am existing can lights. I have two Romex cables. Each one has two black wires and a white wire and a green wire. My ceiling lights are wired in series. Why two black wires?

Did it in less than 2 hours thanks to this video!

Thank you for putting this video together. Our 2005 Hylander had the exact same issue and your video was what I followed to the T to fix our heater issue. Now to get the A/C fixed. Thanks again.

Great job

Brilliant! This is how my 80ft pipe will be sloped in the trench!!! Thank you!!

Awesome video

You dont know the amount of times i’ve watched this video. I’m not even a new driver. I’ve been driving for almost a whole year, yet i still cant remember how to pump gas. I know, embarrassing for me

1 important step (maybe): the two weights can be removed with a 10mm socket so that it’s easier to take off and put on the seal in the back. You did it without removing the weights, but I’m sure it was a little harder to fiddle with the seal.

Good video man.. have done this several buildings myself… I’m glad to see that I’m not the only one doing it.. your 100% right tho … def works and gets better on every post every job

what if garage is complete and slab is in place. Do you just need to dig some of it up and follow from there?

Thanks for sharing! I know iPhone X is very old (probably almost obsolete) by now, but mine has a lot of sentimental value, and I needed it more quickly than a shop could return it. I just finished replacing the screen, battery, and charging port about 2 hours ago with the help of this video, and after a small mishap (totally user error) where the screen came disconnected briefly, I was able to open it up again and reconnect it and now it's working great! My fiance had it repaired at a shop about 3 years ago, replacing the screen and battery, and it cost $250. I've just done that, plus the charging port, and a new screen protector for about $50!

Good video.

BATTERIES ARE A DRAWBACK..,......

I BET THE LAWYER COULD PICK IT IN TWO MINUTES........

Just curious why you chose pole barn construction if you planned on using regular construction materials in all the walls driving up the costs? Wouldn’t it have been about the same price for traditional stick built?

How did this hold up over the years without sinking the legs in concrete? curious if it was find with the anchors

When you installed the new handle, was the license plate plastic trim sticking out? It seems that the all metal plastic handle is not a perfect fit. Any recommendations?

I might work as a gas attendant. What happens if someone asks, “Twenty, regular”?

Holy shit bro you saved my life.

Do you live in an area that has mountain lions? In your video at the 35-36 second mark check out the window reflection.

lol why didn’t they teach us this too they did the driving part now we’re left on empty panicked because we have never done this